Turnigy a6 10 manual install#
Turnigy a6 10 manual series#
Turnigy a6 10 manual download#
Turnigy a6 10 manual free#

Turnigy a6 10 manual install#

windows: install Microsoft File Checksum Integrity Verifier.check the sha1 sum of the file, compare it with *.sha1:.

Turnigy a6 10 manual download#

download the *.hex again, use the 'RAW' button in github.

After flashing charger doesn't work (display shows squares):.

reset the charger to default settings (go to: 'options'->'reset default' and press the 'start' button).

After flashing I see 'options' and some strange characters in the second line (for example: squares), what should I do?.

Calibration - Expert (IMAX B6) - optional Building from Source Troubleshooting If you have any problems with calibration, go to 'options'->'reset default' and try again.

when needed: external (or internal) temperature probe calibration: go to 'temp extern' ('temp intern').

WARNING: the battery will be discharged with high current!

discharge current calibration: go to 'I discharge'.

WARNING: the battery will be charged with high current! Press 'Inc', 'Dec' buttons until the amperemeter shows 1000mA Press 'Inc', 'Dec' buttons until the amperemeter shows 50mA (100mA on some versions) Press 'start' button (current flow should be visible on amperemeter)

Turnigy a6 10 manual series#

connect your amperemeter in series with the battery, use the 10A(20A) input.you need to change at least one value (this will copy V1-6 voltage to Vbat).only Vb1 is mandatory, battery main leads and balance port must be connected.use a voltmeter to measure voltage on all cells and the power supply voltage (Vin)Īnd set voltage on Vin, Vb1, Vb2.To the main leads and the balance port first two pins

charger is working now, press 'inc', 'dec' to see more screensĬonnect a NOT fully charged LiPo battery to the main leadsĪnd the balance port, if you don't own a battery with aīalance connector, just connect a regular one (~4V).

hold 'start' button for 2s to start the program.

(if you hear beeps, check your battery connections)

select program: 'charge', 'discharge'.

set time limit 'Tlim:' (can be unlimited).

set battery voltage (number of cells) 'V:'.

Turnigy a6 10 manual free#

select a free battery slot (indicated as 1., 2.).

Reset the charger to its default settings ('options'->'reset default')Īnd then calibrate it, now your charger is ready to use. others, do your research or ask on the forumĪfter flashing your charger the first thing you should do is to Unsupported due to old or uncommon CPU See #106

Redox Beta 50W 5A charger (at least later model with yellow soldermask).

Thunder T610 Balance Charger/Discharger.

Turnigy MEGA 400Wx2 Battery Charger/Discharger (800W).

Turnigy Accucel-8 150W 7A Balancer/Charger.

Turnigy Accucel-6 50W 5A Balancer/Charger w/ Accessories.

Turnigy A-6-10 200W Balance charger & discharger.

AC/DC Dual Power B6AC 80W RC Balance Charger/Discharger.

Only chargers with a atmega32 or M0517LBN CPU are supported. WARNING: You can get two chargers with the same name but different CPUs even if you buy from the same seller.

Overcharge and overdischarge monitoringĪLWAYS connect the power supply first, then the battery!ĪLWAYS disconnect the battery before disconnecting the power supply! Hardware.

Internal and external temperature monitoring.

terminates charging when the current lowers to 20% of Ic.

terminates charging when the current lowers to 10% of Ic (by default, adjustable in battery settings).

Over all I would have to give this charger a Five Star rating.This project is an alternative firmware for a variety of lipo chargers, I had no trouble at all charging all of these batteries. I also charged some NIMH, NICD, and PB batteries. I can even charge my Nano-Tech batteries from Hobbyking in less than ten minutes, which is pretty impressive. It also doesn't seem to be out of calibration like I heard about with the ECO 6-10 charger from HK. I like that because you can connect the charger to your field battery.Īfter lots of testing, I found that it charges my batteries very well. The input power leads are alligator clips. I bought SEPARATELY a temperature probe so I can see the temp of the charging battery for added safety. You also get a lead that has an XT60 to alligator clips to charge a PB battery. In the box you get a set of banana plugs to XT60, XT60 to Futaba, JST, and Glow plug. The power supply I will be using is the TGY-20 Pro. This charger is capable of charge/balance charge Lipo/Life/Lilo, charge NiMH, NiCD, and PB (field batteries). This is a review of the Turnigy A-6-10 200W Balance Charger.